Il 08/05/2013 14:10, Fabio Mosti ha scritto:
ho provato, la procedura di configurazione sembra andare a buon fine ma poi
faxgetty mi logga "/dev/ttyACM0: can not initialize modem" e di fatto
l'accrocchio non funziona (accoda i fax ma non invia nulla)
cosa posso controllare?
che in /etc/hylafax il file config.ttyACM0 sia simile a questo:
CountryCode: 39
AreaCode: 051
FAXNumber: +39.051.xxx.yyyy
LongDistancePrefix: 00
InternationalPrefix: 000
DialStringRules: etc/dialrules
ServerTracing: 1
SessionTracing: 11
RecvFileMode: 0666
LogFileMode: 0666
DeviceMode: 0666
RingsBeforeAnswer: 1
SpeakerVolume: off
GettyArgs: "-h %l dx_%s"
LocalIdentifier: "Saluti e baci"
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "From %%l|%c|Page %%P of %%T"
MaxRecvPages: 100
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType: Class1 # use class 1 interface
ModemRate: 19200 # rate for DCE-DTE communication
ModemFlowControl: rtscts # software flow control
#
ModemSetupDTRCmd: ATS13=1&D3 # setup so DTR drop resets modem
ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or
not)
ModemNoFlowCmd: AT&H0 # setup modem for no flow control
ModemHardFlowCmd: AT&H1 # setup modem for hardware flow control
ModemSoftFlowCmd: AT&H2 # setup modem for software flow control
ModemResultCodesCmd: ATQ0X4 # enable result codes
#
ModemMfrQueryCmd: !USR
ModemModelQueryCmd: ATI3
ModemRevQueryCmd: ATI7 # XXX returns a multi-line result
#
# When AT+FCLASS=1 is issued the modem automatically switches
# to software flow control; these parameters let the fax software
# reset flow control as needed after entering Class 1.
#
Class1NFLOCmd: AT+FLO=0 # setup modem for no flow control
Class1HFLOCmd: AT+FLO=2 # setup modem for hardware flow control
Class1SFLOCmd: AT+FLO=1 # modem does this automatically
#
# This should resolve "DIS/DTC received 3 times" errors:
#
Class1ResponseWaitCmd: AT+FRS=1 # wait after sending TCF for response
#
# The remainder of this configuration is included so that the
# modem "idles" in Class 0 while not sending or receiving facsimile.
#
ModemSetupAACmd: AT+FCLASS=0 # leave modem idling in class 0
##ModemAnswerCmd: AT+FCLASS=1A # answer in Class 1
#
# When using AT+FRS=n we see USR modems reset themselves in the middle of
sessions
# this is not good. So, we seem to work-around that problem by not using the
# command. Unfortunately, this isn't an ideal thing.
#
Class1SwitchingCmd: "<delay\0727>"
MaxSetupAttempts: 10
ModemAnswerCmd: ATA # string, command for answering phone
ModemAnswerDataBeginCmd: "" # string, command for start of answered
data call
ModemAnswerDataCmd: ATA # string, command for answering data
call
ModemAnswerFaxBeginCmd: "" # string, command for start of answered
fax call
ModemAnswerFaxCmd: ATA # string, command for answering fax call
ModemAnswerResponseTimeout: 180000 # integer, answer command timeout (ms)
ModemAnswerVoiceBeginCmd: "" # string, command for start of answered
voice call
ModemAnswerVoiceCmd: ATA # string, command for answering voice
call
ModemATCmdDelay: 0 # integer, delay before sending modem
an AT cmd (ms)
ModemBaudRateDelay: 0 # integer, delay (ms) after setting
baud rate
ModemClassQueryCmd: AT+FCLASS=? # string, command for querying
modem services
ModemCommaPauseTimeCmd: ATS8=2 # string, command for setting time to pause
for comma in dialing string
ModemDialCmd: ATDT%s # string, command for dialing (%s for
number to dial)
ModemDialResponseTimeout: 180000 # integer, dialing command timeout (ms)
ModemEchoOffCmd: ATE0 # string, command for disabling command
echo
ModemFlowControl: None # string, DTE-DCE flow control scheme
ModemFrameFillOrder: LSB2MSB # string, bit order for HDLC frames
ModemHardFlowCmd: "" # string, command for setting hardware flow control
between DTE and DCE
ModemMinSpeed: 2400 # string, minimum acceptable transmit
speed
ModemMfrQueryCmd: "" # string, command for querying modem
manufacturer
ModemModelQueryCmd: "" # string, command for querying modem model
ModemNoAutoAnswerCmd: ATS0=0 # string, command for disabling
auto-answer
ModemNoFlowCmd: "" # string, command for disabling hardware flow control
between DTE and DCE
ModemOnHookCmd: ATH0 # string, command for placing phone
``on hook''
ModemPageDoneTimeout: 180000 # integer, page send/receive timeout
(ms)
ModemPageStartTimeout: 180000 # integer, page send/receive timeout
(ms)
ModemRate: 19200 # integer, baud rate to use for DCE-DTE
communication
ModemRecvFillOrder: LSB2MSB # string, bit order for received
facsimile data
ModemResetCmds: "" # string, additional commands when
resetting modem
ModemResetDelay: 2600 # integer, delay (ms) after sending
modem reset commands
ModemResultCodesCmd: ATQ0 # string, command for enabling result
codes
ModemRevQueryCmd: "" # string, command for querying modem
firmware revision
ModemSendBeginCmd: "" # string, command to send on establishing
carrier
ModemSendFillOrder: LSB2MSB # string, bit order for sending
facsimile data
ModemSetVolumeCmd: "ATL3M1" # string, commands for setting modem speaker
volume level
ModemSetupAACmd: "" # string, command for setting up adaptive
answer
ModemSetupDCDCmd: "" # string, command for setting up DCD
handling
ModemSetupDTRCmd: "" # string, command for setting up DTR
handling
ModemSoftFlowCmd: "" # string, command for setting software flow control
between DTE and DCE
ModemSoftResetCmd: ATZ # string, command for doing a soft reset
ModemType: Class1 # string, modem type
ModemVerboseResultsCmd: ATV1 # string, command for enabling verbose result
codes
ModemWaitForConnect: No # boolean, force server to wait for ``CONNECT''
response on answer
ModemWaitTimeCmd: ATS7=60 # string, command for setting time to wait for
carrier when dialing
Class1Cmd: AT+FCLASS=1 # string, command to enter
class 1
Class1HFLOCmd: "" # string, command to set hardware flow
control
Class1FrameOverhead: 4 # integer, extra bytes in a received
HDLC frame
Class1NFLOCmd: "" # string, command to set no flow control
Class1RecvAbortOK: 100 # integer, max wait (ms) for ``OK''
after recv abort
Class1RecvIdentTimer: 35000 # integer, max wait (ms) for initial
ident frame
Class1SFLOCmd: "" # string, command to set software flow
control
Class1TCFMaxNonZero: 10 # integer, max% of non-zero data in
good TCF
Class1TCFMinRun: 1000 # integer, minimum zero run in good TCF
Class1TCFRecvTimeout: 4500 # integer, max wait (ms) for TCF
Class1TCFResponseDelay: 75 # integer, delay between TCF and ack/nak
Class1SendPPMDelay: 75 # integer, delay before sending
post-page message
Class1SendTCFDelay: 75 # integer, delay between sending DCS
and TCF
Class1TrainingRecovery: 1500 # integer, delay after failed training
--
Andrea
Registered Linux User #24583
skype://amennini
Egoista, s.:
Uno che non pensa mai a me.
|